![]() ![]() Press and hold the Feed button on the front of the printer while the printer is turned off.ģ. Switch your printer off using the power switch.Ģ. Printing your Network Configuration and Current IP Parametersġ. To achieve an AP network connection, the printer should be connected to your router using an ethernet cable. This involves printing your network configuration and current IP Parameters and setting your wireless LAN settings. Retry steps 1 and 2 again to ensure the printer is paired to the network. ![]() If the IP address on the receipt says "NONE" or "0.0.0.0", the printer is not connected to the internet. This will be your printer's new dynamic IP address. Under Current IP Parameters, make a note of the IP Address. The Ready light on the printer will now be solid and your Network Configuration and Current IP Parameters Status will print out automatically.Ĥ. This will establish a connection between your printer and your router. Steps 1 and 2 have to be done within 30 seconds of each other. The usage procedure of the access point or router will vary according to the device. Press and hold the red Pair button on the back of your printer until the blue light on the front of your printer starts blinking.Ģ. However, if your router does not support WPS, use the steps under Connect by AP network mode instead.ġ. The simplest way to connect your printer is by a WPS. You are now ready to connect your printer to your wireless network. Turn your printer on and wait for the blue light to stop blinking. Connect the Star TSP100/TSP100III to a power source using the provided power cableĢ. Using the dedicated app (TSP100III Utility Mac/iPad) will help you set your product up easily.ġ. This is a specialized cash drawer cable that is similar looking to an ethernet cable but is smaller on one end. You may also wish to set up your cash drawer at the same time, to do this you'll need an RJ12 cable. To load your receipt roll open the latch on the top right of the printer, place the roll inside, and pull some of the paper through before closing the lid. You will need a power cable for the printer. To set up your receipt printer with your PC, Mac, or iPad, you'll first need to make sure you have all the peripherals needed. Select the tab for your device platform (Mac, Windows PC, or iPad) and follow the provided steps.įor more information on your TSP 100III Wireless Printer, refer to Star's Online Manual. ![]() This guide provides step-by-step instructions to connect your Star TSP100III wirelessly to your internet router and provide wireless receipt printing. To fix this, ensure your device's Bluetooth and Local Network Permissions are enabled in Settings > Lightspeed Retail POS (X). If declined, this will cause your printer to no longer function. If your POS is set up to require a signature, ensure that your signature pad is properly set up by following the instructions in this Knowledge Base article.Important: Updating to iOS 14+ on iPad will prompt you to grant the Retail POS app permissions to access Bluetooth and Local Network settings on your iPad. To prevent this from continuing to appear, click Don't ask again for this site, then click Allow.Ħ. Note: When attempting to print your first receipt, a permission pop-up will appear. To cancel the print, click the X in the top right corner of the window. This pop-up will automatically disappear once the receipt is printed. A pop-up will appear, indicating that the receipt is printing. Use your cursor to set the top, bottom, left, and right margins to. Select Star TSP100 Cutter as the destination. When the Setup Wizard appears, click Next to continue.Ħ. Once the driver is installed, click Finish.ħ. Proceed to the Chrome page setup instructions below.ġ. Open Chrome settings by clicking on the menu button in the top right corner. Click the file to continue installation.Ĥ. A permission window will appear, asking if you would like to let JSPrintManager make changes to your device. exe file will appear in the lower left hand corner of Chrome. If you are unsure, select Unified Installer.ģ. The downloaded. NOTE: Please confirm the version 4 has been selected.Ģ. Select the driver that corresponds to your Windows version. Ensure that JSPM for Windows is selected. Open this link to navigate to the JSPrintManager installation page. This article will guide you through configuring your Star TSP100 Printer for use with Google Chrome.ġ. Configure Your Star TSP100 Printer For Use With Chrome ![]()
0 Comments
Leave a Reply. |